Website

 

How do you really feel on the subject of A Step-by-Step Guide to Installing a Bathtub?

Setting up a bathtub isn't precisely brain surgery, yet it does need strong plumbing, carpentry, and also often, tiling skills. Replacing an old bath tub with a new one is additionally a moderately tough project. If the old tub is conveniently obtainable, the task can relocate easily; if you need to open up a wall surface to get rid of the old bathtub as well as place the new bathtub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly require a helper to vacate the old bathtub and set in the new one. Make sure you have actually certified on your own for the job as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed job, it is better to think about employing one prior to you begin. Opportunities are you might need an expert plumber to make tube connections.
This short article will help you mount a new tub in your shower room if you have actually already bought a brand-new bathtub as well as do not need to transform the plan of your previous water pipes.
Your tools and also product checklist need to consist of the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipe Caps


 

Planning for the Setup

To start with, the supporting frame provided with the bath should be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to ensure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets device to prevent strain on the tub.
Fit the flexible faucet connectors to the bottom of both faucets utilizing 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you use every one of the supplied washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should now prepare to be fitted in its final position.

 

 

Removing Old Taps

If you need to replace old taps with new ones as a part of your setup, then the first thing you ought to do is detach the water. After doing so, turn on the faucets to drain any type of water staying in the system. The procedure of removing the existing taps can be quite problematic due to the limited accessibility that is usually the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipelines have been removed, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from transforming during this procedure. As soon as the faucets have been eliminated, the holes in the bath/basin will have to be cleaned up of any old securing substance.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the new taps to fit.

 

 

Installing the Bathtub

Using both wooden boards under its feet, put the bath tub in the required placement. The wooden boards are useful in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 tiny factors.
The following objective is to guarantee that the bath tub is leveled all round. This can be attained by examining the level as well as changing the feet on the tub till the spirit level checks out degree.
To mount taps, fit all-time low of the outermost flexible tap connector to the suitable supply pipe by making a compression sign up with; after that do the same for the other tap.
Turn on the water system and inspect all joints and new pipework for leakages and tighten them if necessary. Fill the tub as well as likewise check the overflow electrical outlet and also the normal electrical outlet for leaks.
Finally, deal with the bathroom paneling as described in the producer's instruction manual. Tiling and securing around the bathtub should wait till the bath tub has actually been used a minimum of when as this will certainly settle it right into its final position.

 

 

Suitable New Touches

If the tails of the new taps are plastic, then you will need a plastic connector to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and the other end offers a link to the current supply pipes.
If you need to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin ensuring that the washers remain in place in between the tap as well as the sink. Secure the tap in place with the manufacturer supplied backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular tap ports. The former type needs to be connected to the tap finishes first, tightening up only by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been attached.

 

 

Tiling Around the Tub

In the area where the bathroom fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to fracture a rigid seal, creating the water to pass through the wall surface between the bathroom as well as the tiling, resulting in complications with wetness and also feasible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your components and also fittings. They are marketed in tubes as well as cartridges, as well as are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill the bathtub with water prior to securing, to enable the motion experienced when the bathtub is in usage. The sealer can fracture fairly very early if you do not take into account this motion before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently offered on the marketplace. It is a good idea to fit the tiles utilizing waterproof or waterproof sticky and cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I hope you liked our section on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you for taking the time to read our article post. Loved our post? Please share it. Let somebody else find it. Many thanks for taking the time to read it.

Excellence on call!